Richard Mille RM 011-03 Super Clone : Titane Automatic Flyback Chronograph

Tonneau Case, Crown and Lug Profile  50mm Grade 5 Titanium Build

The Richard Mille RM 011-03 super clone carries a tonneau case measuring 50mm long by 42.70mm wide and 16.15mm thick, machined to the curved Richard Mille silhouette that the RM 011 line defined for the flyback chronograph category. The case uses grade 5 titanium across the bezel, the caseband, and the caseback, with mixed polished and satin finishes that follow the genuine RM 011-03 surface treatment. Six grade 5 titanium spline screws ring the bezel and tie into the engineered look of the line. The screw-down crown at 2 o'clock seals the case for water resistance to 50 meters, and the function selector pusher at 4 to 5 o'clock cycles the crown function across NEUTRAL, WIND, DATE, and TIME positions in line with the RMAC3 architecture.

Full Grade 5 Titanium Construction and Surface Finishing

The full grade 5 titanium build of the RM 011-03 super clone delivers a strong, light, hypoallergenic case structure that defines the modern Richard Mille catalogue identity. Grade 5 titanium, the Ti-6Al-4V aerospace alloy, carries roughly 40% less weight than steel at higher tensile strength, which is the reason Richard Mille uses it as the structural baseline of the RM 011 line. The case finish mixes polished and satin surfaces across the bezel facets, the caseband, and the lugs to deliver the layered light play that the genuine RM 011-03 shows under angled light. This super clone follows the genuine titanium specification and the finish layout so the case reads correctly under close inspection on weight, edge geometry, and surface texture.

Sapphire Crystal, Sapphire Caseback and Function Selector

Scratch-resistant sapphire crystal with anti-reflective coating covers the skeletonised dial and lets full light through to the open bridges and the registers below. The curved sapphire follows the tonneau profile and stays clear under angled light, a signature look of the RM 011 line. The sapphire caseback shows the automatic flyback chronograph clone movement from below, including the variable geometry rotor, the column wheel, and the gear train. The function selector pusher at 4 to 5 o'clock works with the crown to cycle through NEUTRAL, WIND, DATE, and TIME, with the active function indicated through the dial-side selector ring near the lower right, the same control layout the genuine RMAC3 caliber uses.

Skeletonised Dial with Open Bridges and Titanium Tones

The skeletonised dial of this RM 011-03 super clone shows the movement bridges, the column wheel, the going train, and the chronograph linkages from the front, with no traditional dial plate covering the architecture. The titanium-toned bridges sit against the open chassis to deliver the layered industrial look of the third-generation RM 011, and the open design lets the buyer read both the time and the chronograph mechanics through the sapphire. This super clone matches the bridge cut-out shape, the satin and polished finishing on the bridges, and the open architecture of the genuine RM 011-03 Titane production.

Oversized Date, Flyback 30-Minute Counter and Small Seconds

The dial layout follows the RM 011-03 register signature with the oversized date display at 12 o'clock under a magnified aperture for direct daily reading, the flyback chronograph 30-minute counter at 4 to 5 o'clock for measured timing intervals, and the running small seconds sub-dial at 9 o'clock for at-a-glance proof of life. The applied white-gold-toned hour markers ring the chapter ring with luminous inserts for low-light reading, and the central chronograph seconds hand sweeps from rest at 12. The flyback function lets the wearer reset and restart the chronograph through a single pusher push without first stopping the running register, which is the timing convenience that defines the RM 011-03 daily use.

Function Selector Indication and Legibility

A function selector indication ring near the lower right of the dial shows which mode the crown is set to across the four positions of NEUTRAL, WIND, DATE, and TIME, which is the signature control feature of the RMAC3 caliber that the third-generation RM 011 carries. The white-gold-toned markers and the skeleton hands hold legibility against the open bridges through tonal contrast, and the chapter ring carries the minute and second tracks around the outer edge for precise chronograph reading. The titanium bezel frames the dial without colour interference, which keeps the focus on the registers and the movement architecture underneath.

Swiss-Grade RMAC3 Clone Automatic Flyback Chronograph

The Richard Mille RM 011-03 super clone runs on a Swiss-grade automatic flyback chronograph movement engineered to match the genuine Richard Mille RMAC3 caliber in feel, frequency, and architecture. The movement operates at 28,800 vibrations per hour, winds automatically through a variable geometry rotor, and holds a power reserve of approximately 55 hours for over two days off the wrist. The caliber drives the central hours and minutes, the small seconds at 9 o'clock, the flyback 30-minute chronograph counter at 4 to 5 o'clock, the oversized date at 12 o'clock, and the function selector indication across a grade 5 titanium baseplate and grade 5 titanium bridges, the same architectural choice the genuine RMAC3 uses for shock resistance and weight reduction.

Flyback Function, Accuracy and Daily Performance

The flyback chronograph lets the wearer reset and restart the elapsed-time counter through a single pusher action without first halting the running register, which suits sport timing intervals and lap-style timekeeping. Daily deviation holds within -4 to +8 seconds per day after factory regulation, close to the chronometer band that buyers expect from a Swiss-grade automatic build at 4 Hz. The grade 5 titanium baseplate and bridges give the movement a strong, light core that handles shock during active wear, and the variable geometry rotor lets the winding efficiency adjust to the wearer's activity level for stable autonomy. The 50-meter water resistance, the screw-down crown, and the sealed function selector pusher let the RM 011-03 super clone hold its seal through daily wear, hand washing, and light water contact.

Spec grid:

Black Rubber Strap and Titanium Folding Buckle

The RM 011-03 Titane super clone carries a black rubber strap, the strap configuration Richard Mille pairs with the pure titanium catalogue trim. The strap uses a soft, flexible rubber compound with a fine ribbed texture along the surface that holds its shape across long-term wear, with integrated lugs that flow into the tonneau case for the continuous Richard Mille silhouette. A grade 5 titanium folding buckle closes flush against the wrist for a secure hold and lets the buyer remove the watch without flexing the strap repeatedly, with the buckle finish matching the polished and satin treatment of the case.

Wrist Feel, Sizing and Comfort

The watch weighs approximately 90 grams on the full black rubber strap, which gives the RM 011-03 the light wrist presence buyers expect from a full grade 5 titanium Richard Mille chronograph. The 50mm by 42.70mm tonneau case wears closer to a 44mm round watch on the wrist due to the curved geometry and the short lug-to-lug span, and the 16.15mm height clears most shirt cuffs on a folding buckle. The RM 011-03 Titane Super Clone sits comfortably on wrists from 6.5 to 8.25 inches with the titanium folding buckle adjusted across the strap holes.