Richard Mille RM 11-03 Super Clone : Titanium White Flyback Chronograph

Tonneau Case, Crown and Lug Profile — 50mm Grade 5 Titanium Build

The Richard Mille RM 11-03 Titanium White super clone carries a tonneau case measuring 50mm long by 42.70mm wide and 16.15mm thick, machined to the curved Richard Mille silhouette the RM 011 family established. The case uses grade 5 titanium for the bezel, caseband, and caseback ring, finished with alternating polished and satin surfaces that catch light along the contoured edges. Six titanium spline screws ring the bezel and tie into the engineered structural look of the RM 11-03, and the screw-down crown at 2 o'clock seals the case to 50 meters of water resistance.

Grade 5 Titanium Construction and Surface Finishing

The grade 5 titanium case of the RM 11-03 super clone delivers a strong, light, and corrosion-resistant build that keeps the watch under 90 grams on the rubber strap. Grade 5 titanium, the same Ti-6Al-4V alloy used in aerospace structural parts, holds the dimensional precision needed for the tight tolerances of the tonneau case and resists daily wear marks better than stainless steel. The polished and satin finishing across the bezel and caseband replicates the dual-texture surface the genuine RM 11-03 carries, with crisp transitions between brushed flats and polished bevels. This super clone follows the genuine titanium construction so the RM 11-03 reads correctly under close inspection on weight, surface contrast, and edge geometry.

Sapphire Crystal and Sapphire Caseback

Scratch-resistant sapphire crystal with anti-reflective coating covers the skeletonised dial and lets full light through to the open bridges below. The curved sapphire follows the tonneau profile and stays clear under angled light, a signature look of the RM 11-03. The sapphire caseback shows the automatic flyback chronograph clone movement from below, including the variable-geometry rotor and the chronograph bridges, and the screw-down crown supports the 50-meter water resistance of the reference.

Skeletonised Dial with White-Toned Markers

The skeletonised dial of this RM 11-03 super clone shows the movement bridges, the chronograph wheels, and the going train from the front, with no traditional dial plate covering the architecture. Applied white-toned hour markers run around the chapter ring in baton form, with white-painted minute indices on the outer track for precise time reading against the open bridges. This Titanium White build matches the marker placement, the chapter-ring print, and the applied "Richard Mille" branding of the genuine titanium-and-white reference.

Oversized Date, Flyback Chronograph and Small Seconds Layout

The RM 11-03 displays an oversized date in a window at 12 o'clock, a flyback 30-minute chronograph counter at 4-5 o'clock, and a small seconds subdial at 9 o'clock, each framed by white-accented rings. The 12-hour chronograph counter sits at 9 o'clock, integrated into the small seconds register, and the function selector indicator sits adjacent to the 4-5 o'clock pusher and shows the W-N-H (Winding, Neutral, Hand-setting) position selected through the crown. The subdial layout, the oversized date placement, and the white ring accents follow the Titanium White production layout of the genuine RM 11-03.

Function Selector Pusher and Pusher Architecture

A function-selector pusher at 4-5 o'clock lets the wearer cycle the crown between winding, neutral, and hand-setting positions without using the crown push-pull stem. The chronograph start-stop pusher sits at 2 o'clock and the reset pusher sits at 8 o'clock, both in skeletonised titanium form with white accents to match the dial palette. The flyback function lets the user reset and restart the chronograph through a single push of the reset pusher while the chronograph runs, a feature borrowed from pilot watch tradition that the RM 11-03 carries onto the tonneau platform.

Swiss-Grade RMAC3 Clone Automatic Flyback Chronograph Movement

The Richard Mille RM 11-03 super clone runs on a Swiss-grade automatic flyback chronograph movement engineered to match the genuine Richard Mille RMAC3 caliber in feel, frequency, and architecture. The movement operates at 28,800 vibrations per hour, winds automatically through a variable-geometry rotor, and holds a power reserve of approximately 55 hours for over two days off the wrist. The caliber drives the hours, minutes, small seconds, oversized date, flyback chronograph, and function selector across a grade 5 titanium baseplate and bridges, the same architectural choice the genuine RMAC3 uses for shock resistance and weight reduction.

 Variable-Geometry Rotor and Adaptive Winding

The variable-geometry rotor of the RM 11-03 super clone uses adjustable side blades that change the rotor's inertia to match the wearer's activity level. The rotor winds faster on an active wrist and slower on a desk-bound wrist, which keeps the mainspring close to full charge across daily wear cycles. The grade 5 titanium rotor sits behind the sapphire caseback and stays visible through the open architecture. This clone build follows the variable-geometry geometry and the rotor weight distribution of the genuine RMAC3, so the winding behaviour tracks the original caliber.

Accuracy, Shock Resistance and Daily Performance

Daily deviation holds within -5 to +8 seconds per day after factory regulation, close to the chronometer band buyers expect from a Swiss-grade automatic chronograph. The grade 5 titanium baseplate and bridges give the movement a strong, light core that handles shock during active wear, which is the architectural reasoning behind the genuine RMAC3. The 50-meter water resistance and the screw-down crown let the RM 11-03 super clone hold its seal through daily wear, hand washing, and light water contact, in line with the sport-luxury positioning of the reference.

Spec grid:

White Rubber Strap and Titanium Folding Buckle

The RM 11-03 Titanium White super clone carries a white rubber strap, the strap style Richard Mille pairs with the lighter titanium colourways of the reference. The strap uses a soft, flexible rubber compound that holds its shape across long-term wear, with integrated lugs that flow into the tonneau case for the continuous Richard Mille silhouette. A grade 5 titanium folding buckle closes flush against the wrist for a secure hold and lets the wearer remove the watch without flexing the strap repeatedly. This Titanium White build uses the white rubber strap on the titanium case as a deliberate visual pairing, not a metal bracelet.

Wrist Feel, Sizing and Comfort

The watch weighs approximately 88 grams on the full white rubber strap, which gives the RM 11-03 the light wrist presence buyers expect from a titanium Richard Mille chronograph. The 50mm by 42.70mm tonneau case wears closer to a 44mm round watch on the wrist due to the curved geometry, and the 16.15mm height clears most shirt cuffs with the strap dressed under the cuff line. The Titanium White Super Clone sits comfortably on wrists from 6.5 to 8 inches with the folding buckle adjusted across the strap holes.